IGene Labserve Private Limited

SpecificationsBiosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant freeenvironment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because  such BSCs effectively eliminate risks to operator / staff, samples and the environment frompathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.
TypesWe offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:

Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air.

Construction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel
Air Circulation of Class II B2In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality. Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separate exhaust mechanism.

Standard Accessories
Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly. Microprocessor controlled mechanism allows UV on only when door is closed. Auto sensors facilitate to run blower after opening of door only. User can set warm time as per convenience which in turn will tun on the FL light only after set time and door open controlled by microprocessor. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand We also manufacturer biosafety cabinets class 2 type A2. 

Microprocessor based PID Controller

Automatic control of UV, Blower and LED light on sash movement. Large LCD Display with clear vision. External Socket control to avoid hand touch inside the chamber Warm up timer option allows delay in switching on LED to clear internal air before working on opening of Sash to safe level

Specialised workstations known as biosafety cabinets are frequently found in industrial, pharmaceutical, clinical, and life science labs where very contaminant-free environments are required for investigations. Biological safety cabinets, sometimes referred to as biohazard safety cabinets, are manufactured in three distinct class types: Class 1, Class 2, and Class 3. Class 2 is commonly utilised in microbiology labs because to its ability to protect both personal and product items. Which BSC should be utilised in a laboratory depends on the biosafety level factor. Because these BSCs successfully remove the hazards that pathogenic biological agents (PBA) and microbes that propagate airborne infections provide to operators, workers, samples, and the environment, these cabinets are thought to be safer than alternative clean benches. Types We provide three different kinds of class 2 biosafety cabinets. Which class 2 BSC should be utilised in the lab depends on the nature of the job. A brief summary of each type we provide is provided below: Recirculate around 70% air and 30% exhaust for Type A2, and 30% air and 70% exhaust for Type B1. Type B2: Does not recirculation but expel 100% air Building Our cabinets have a long service life because of their ergonomic design. To provide you with the best and safest Biosafety Cabinet available on the market today, only thick metal sheets and pipes are utilised in construction. Three distinct MOCs are employed. Whole 304/316 stainless steel Stainless steel on the inside, mild steel on the outside.

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.

Types

There are three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction

These cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.
Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air Circulation

In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type A2 safety cabinets. These air filters are of reputed brands in the market, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply and exhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec), while down low velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and 30% exhaust.

Standard Accessories 

Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly. An hour meter is connected to UV lamp. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.

Types
We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction

Our cabinets are ergonomically designed to provide long service life. Only thick metal sheet and pipes are used in construction so that you may get the finest and safest Biosafety Cabinetin the market today.
There are three different MOC used.

Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air Circulation of Class II B2In order to minimize spread of airborne bacterial and viral organisms, the use of filter iscrucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in ourbiological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality.Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separateexhaust mechanism.
Standard Accessories
Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps arefitted inside working zone in such a way that the operator cannot see them directly.Microprocessor controlled mechanism allows UV on only when door is closed. Auto sensorsfacilitate to run blower after opening of door only. User can set warm time as per convenience which in turn will tun on the FL light only after set time and door open controlled by microprocessor. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand

Specifications:

Biosafety Cabinets are specialized workstation widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.
Types:

There are three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes:

Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction:

These cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.

- Complete Stainless Steel 304 / 316- Inner Stainless Steel, Outer Mild Steel- Stainless Steel bench, rest mild Steel

Air Circulation:

In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type A2 safety cabinets. These air filters are of reputed brands in the market, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply andexhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec), while down flow velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and 30% exhaust.

Standard Accessories:

Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly. An hourmeter is connected to UV lamp. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand.

We also manufacturer biosafety cabinets class 2 type B1 and B2

SPECIFICATION

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection

Construction

·         Complete Stainless Steel 304 / 316

·         Inner Stainless Steel, Outer Mild Steel Stainless

·         Steel bench, rest mild Steel

Air Circulation of Class II B2

In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality. Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separate exhaust mechanism.

Specifications :-

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection. Types We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about all types we offer:

Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air
Construction

Our cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used. Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild Steel Stainless Steel bench, rest mild Steel.

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free  environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product aswell as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.
Types
We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about all
B2: Does not recirculate but exhaust 100% air
Construction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheetsand pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today.
Complete Stainless Steel 304 / 316Inner Stainless Steel

Specifications
Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant freeenvironment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment frompathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.
Types
We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air
Construction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air Circulation of Class II B2
In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality.Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separate exhaust mechanism.

Standard Accessories
Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly.Microprocessor controlled mechanism allows UV on only when door is closed. Auto sensors facilitate to run blower after opening of door only. User can set warm time as perconvenience which in turn will tun on the FL light only after set time and door open controlled by microprocessor. Electrical sockets are fitted to run any instrument under theworking area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand.We also manufacturer biosafety cabinets class 2 type A2.

SpecificationsBiosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product aswell as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection..

TypesThere are three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction
These cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel
Air CirculationIn order to minimize spread of airborne bacterial and viral organisms, the use of filter iscrucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in ourbiological class 2 type A2 safety cabinets. These air filters are of reputed brands in themarket, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply and exhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec), while down flow velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and 30% exhaust.In order to minimize spread of airborne bacterial and viral organisms, the use of filter iscrucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in ourbiological class 2 type A2 safety cabinets. These air filters are of reputed brands in themarket, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply andexhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec),while down flow velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and30% exhaust.

Standard Accessories
Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps arefitted inside working zone in such a way that the operator cannot see them directly. An hourmeter is connected to UV lamp. Electrical sockets are fitted to run any instrument under theworking area; in addition, service fixtures for air, gas, vacuum and water are fitted on demandWe also manufacturer biosafety cabinets class 2 type B1 and B2.

Microprocessor based PID Controller

Automatic control of UV, Blower andLED light on sash movement.Large LCD Display with clear vision. External Socket control to avoid hand touch inside the chamber Warm up timer option allows delay in switching on LED to clear internal air before working on opening of Sash to safe level

SpecificationsBiosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, lifescience and industrial laboratories where experiments need highly contaminant freeenvironment. Also known as biological safety cabinets and biohazard safety cabinets, theseare made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2is widely used in microbiology laboratories because it provides protection to both product aswell as personal. It is biosafety level factor which decides which BSC should be used inlaboratory. These cabinets are considered safer than other clean benches becausesuch BSCs effectively eliminate risks to operator / staff, samples and the environment frompathogenic biological agents (PBA) and microorganisms responsible for spreading airborneinfection.TypesThere are three types of class 2 biosafety cabinets are made. It is the type of work whichdecides which class 2 BSC should be used in laboratory. Below is short description about alltypes:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% airConstructionThese cabinets are ergonomically designed to provide long service life. Only thick metalsheets and pipes are used in construction so that you may get the finest and safest BiosafetyCabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel
Air CirculationIn order to minimize spread of airborne bacterial and viral organisms, the use of filter iscrucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in ourbiological class 2 type A2 safety cabinets. These air filters are of reputed brands in themarket, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply andexhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec),while down flow velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and30% exhaust.Standard AccessoriesOur Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps arefitted inside working zone in such a way that the operator cannot see them directly. An hourmeter is connected to UV lamp. Electrical sockets are fitted to run any instrument under theworking area; in addition, service fixtures for air, gas, vacuum and water are fitted on demandWe also manufacturer biosafety cabinets class 2 type B1 and B2
Microprocessor based PID Controller 

Automatic control of UV, Blower andLED light on sash movement.
Large LCD Display with clear vision.External Socket control to avoid handtouch inside the chamberWarm up timer option allows delay inswitching on LED to clear internal airbefore working on opening of Sash tosafe level

Specifications
Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.

Types

We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about all types we offer:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air Circulation of Class II B2
In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality.Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separate exhaust mechanism.

Standard Accessories

Our Biosafety cabinets are fitted with fluorescent lightsoutside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly.Microprocessor controlled mechanism allows UV on only when door is closed. Auto sensors facilitate to run blower after opening of door only. User can set warm time as per convenience which in turn will tun on the FL light only after set time and door open controlled by microprocessor. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demandWe also manufacturer biosafety cabinets class 2 type A2

DESCRIPTION
iGene Maximum operating temperature range of these ovens are 200°C, 250°C and 300°C, which is controlled through microprocessor based PID controller, which displays bothset value (SV) and process value (PV) and plays important role in temperature control.Forced air circulation is maintained using branded motor driven blower system. For heating,we use ceramic bead heating elements or tubular air heaters for high temperature. Each unit is fitted with over temperature protection device (safety thermostat), which keeps your ovensafe in case of controller failure.
SPECIFICATION
Temperature range:Ambient +5°C to 250°C (Optional300ºC)
Temperature accuracy:±1°C
Temperature sensor:PT100
Temperature controller: Microprocessor PID controller/Display of SV & PV.
Shelves:SS wire mesh cable trays (removable)
Door:Insulated solid door with clamp.
50°C to 250°C temperature
Uniform air circulation across chamber
Digital temperature controller cum indicator
Excellent uniformity at high temperature
Stainless steel 304 grade inner chamber
Corrosion resistant exterior
Fume ventilation points on both sides
Stainless steel cable trays 
Over temperature protection.

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, theseare made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches becausesuch BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.
TypesThere are three types of class 2 biosafety cabinets are made. It is the type of work whichdecides which class 2 BSC should be used in laboratory. Below is short description about all
Types:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air
Construction
These cabinets are ergonomically designed to provide long service life. Only thick metalsheets and pipes are used in construction so that you may get the finest and safest BiosafetyCabinet in the market today. There are three different MOC used. 
Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air Circulation
In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type A2 safety cabinets. These air filters are of reputed brands in the market, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply andexhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec), while down flow velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and 30% exhaust.
Standard Accessories Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly. An hour meter is connected to UV lamp. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand

Specifications
Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant freeenvironment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment frompathogenic biological agents (PBA) and microorganisms responsible for spreading airborneinfection.

Types:
There are three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction 
These cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air Circulation
In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type A2 safety cabinets. These air filters are of reputed brands in the market, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply and exhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec), while down flow velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and 30% exhaust.

Standard Accessories
Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly. An hourmeter is connected to UV lamp. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand We also manufacturer biosafety cabinets class 2 type B1 and B2

SpecificationsBiosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product aswell as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches becausesuch BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.

TypesThere are three types of class 2 biosafety cabinets are made. It is the type of work whichdecides which class 2 BSC should be used in laboratory. Below is short description about alltypes:
Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air
ConstructionThese cabinets are ergonomically designed to provide long service life. Only thick metalsheets and pipes are used in construction so that you may get the finest and safest BiosafetyCabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air CirculationIn order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.97% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type A2 safety cabinets. These air filters are of reputed brands in the market, economical in price and easy replaceable. ISO 5 / Class 100 quality, supply and exhaust through HEPA filters are done. Inflow velocity remains approx. 105 fpm (0.5 m/sec), while down flow velocity remains approx. 55 fpm (0.3 m/sec). 70 % air is re-circulated and 30% exhaust.

Standard AccessoriesOur Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps arefitted inside working zone in such a way that the operator cannot see them directly. An hour meter is connected to UV lamp. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand.

We also manufacturer biosafety cabinets class 2 type B1 and B2.

Microprocessor based PID Controller
Automatic control of UV, Blower and LED light on sash movement.Large LCD Display with clear vision. External Socket control to avoid hand touch inside the chamber Warm up timer option allows delay in switching on LED to clear internal air before working on opening of Sash to safe level

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product aswell as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborneinfection.Types
We offer three types of class 2 biosafety cabinets are made. It is the type of work whichdecides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% airConstruction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheetsand pipes are used in construction so that you may get the finest and safest Biosafety Cabinetin the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.

Types
We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:
Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

Air Circulation of Class II B2
In order to minimize spread of airborne bacterial and viral organisms, the use of filter is crucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in our biological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality. Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separate exhaust mechanism.

Standard Accessories
Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly. Microprocessor controlled mechanism allows UV on only when door is closed. Auto sensors facilitate to run blower after opening of door only. User can set warm time as per convenience which in turn will tun on the FL light only after set time and door open controlled by microprocessor. Electrical sockets are fitted to run any instrument under the working area; in addition, service fixtures for air, gas, vacuum and water are fitted on demandWe also manufacturer biosafety cabinets class 2 type A2

Microprocessor based PID Controller
Automatic control of UV, Blower and LED light on sash movement.Large LCD Display with clear vision.External Socket control to avoid hand touch inside the chamberWarm up timer option allows delay in switching on LED to clear internal air before working on opening of Sash tosafe level

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.

Types

We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:

• Type A2: recirculate approximately 70% air and 30% exhaust
• Type B1: recirculate approximately 30% air and 70% exhaust
• Type B2: Does not recirculate but exhaust 100% air

ConstructionOur cabinets are ergonomically designed to provide long service life. Only thick metal sheetsand pipes are used in construction so that you may get the finest and safest Biosafety Cabinetin the market today. There are three different MOC used.

• Complete Stainless Steel 304 / 316
• Inner Stainless Steel, Outer Mild Steel
• Stainless Steel bench, rest mild Steel

Air Circulation of Class II B2In order to minimize spread of airborne bacterial and viral organisms, the use of filter iscrucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in ourbiological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality.Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separateexhaust mechanism.

Standard Accessories
Our Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps are fitted inside working zone in such a way that the operator cannot see them directly.Microprocessor controlled mechanism allows UV on only when door is closed. Auto sensors facilitate to run blower after opening of door only. User can set warm time as perconvenience which in turn will tun on the FL light only after set time and door open controlled by microprocessor. Electrical sockets are fitted to run any instrument under theworking area; in addition, service fixtures for air, gas, vacuum and water are fitted on demand.
We also manufacturer biosafety cabinets class 2 type A2

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, lifescience and industrial laboratories where experiments need highly contaminant freeenvironment. Also known as biological safety cabinets and biohazard safety cabinets, theseare made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2is widely used in microbiology laboratories because it provides protection to both product aswell as personal. It is biosafety level factor which decides which BSC should be used inlaboratory. These cabinets are considered safer than other clean benches becausesuch BSCs effectively eliminate risks to operator / staff, samples and the environment frompathogenic biological agents (PBA) and microorganisms responsible for spreading airborneinfection.TypesWe offer three types of class 2 biosafety cabinets are made. It is the type of work whichdecides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% airConstructionOur cabinets are ergonomically designed to provide long service life. Only thick metal sheetsand pipes are used in construction so that you may get the finest and safest Biosafety Cabinetin the market today. There are three different MOC used.Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel
Air Circulation of Class II B2In order to minimize spread of airborne bacterial and viral organisms, the use of filter iscrucial; therefore, we use 99.95% efficiency HEPA filters for particle size 0.3 microns in ourbiological class 2 type B2 safety cabinets. These air filters are of ISO 5 / Class 100 quality.Inflow velocity remains approx. 105 fpm (0.5 m/sec) with 100% air exhaust through separateexhaust mechanism.Standard AccessoriesOur Biosafety cabinets are fitted with fluorescent lights outside working zone. UV lamps arefitted inside working zone in such a way that the operator cannot see them directly.Microprocessor controlled mechanism allows UV on only when door is closed. Auto sensorsfacilitate to run blower after opening of door only. User can set warm time as perconvenience which in turn will tun on the FL light only after set time and door opencontrolled by microprocessor. Electrical sockets are fitted to run any instrument under theworking area; in addition, service fixtures for air, gas, vacuum and water are fitted on demandWe also manufacturer biosafety cabinets class 2 type A2Microprocessor based PID ControllerAutomatic control of UV, Blower andLED light on sash movement.Large LCD Display with clear vision.External Socket control to avoid handtouch inside the chamberWarm up timer option allows delay inswitching on LED to clear internal airbefore working on opening of Sash tosafe level

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant freeenvironment. Also known as biological safety cabinets and biohazard safety cabinets, thes re made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product aswell as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborneinfection.Types
We offer three types of class 2 biosafety cabinets are made. It is the type of work whichdecides which class 2 BSC should be used in laboratory. Below is short description about all
Types we offer:
Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air
Construction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.

Thermostatic Water Baths are used for various purposes including evaporating, drying, concentrating and thermostatically heating. Widely adopted in medical and research units, factories, universities, chemical dyeing and petroleum
FEATURES

• It adopts new design structure, which could avoid the leakage of steam. 
•  There are pointer type temperature controller and intellectual type temperature controller for selecting. 
•  The intellectual temperature controller has high lightness digital display and key operating button, which is easy to operate.
•  It has high precision on controlling the temperature. 

Thermostatic Water Baths are used for various purposes including evaporating, drying, concentrating and thermostatically heating. Widely adopted in medical and research units, factories, universities, chemical dyeing and petroleum
FEATURES

• It adopts new design structure, which could avoid the leakage of steam. 
•  There are pointer type temperature controller and intellectual type temperature controller for selecting. 
•  The intellectual temperature controller has high lightness digital display and key operating button, which is easy to operate.
•  It has high precision on controlling the temperature. 

Plant Growth Chamber is a chamber having three side illumination, humidity & temperature. It has applications in plant science, soil science & agriculture research etc. The use of plant growth chamber is to create artificial environment using combination of temperature, humidity and light at different set points for biological samples, electronic components and other relevant applications.

DESCRIPTION:

Construction:
We construct the inner chamber of machine with thick gauge of stainless steel 304 & exterior with powder coated GI sheet for corrosion resistance surface. High density PUF insulation of 70mm is filled between inner and external walls. Main chamber is fabricated with arc welding. We construct sizes as small as 100 litres to 1200 litres or customize as per user requirement. Caster wheels with brake are fitted for easy movement. Doors: We use double door mechanism with inner door for observation which is fixed directly to the inner chamber that give you access to view plants inside without any variation in internal atmosphere. The exterior door is insulated and fixed with easy to use latches.

Temperature & Humidity:
The temperature range is 5°C to 60°C and humidity range is 50% to 90%. These parameters are controlled through PID controller with excellent accuracy and uniformity through PT100 temperature and capacitive humidity sensors. High Quality heaters are used for temperature. For humidity, stainless steel tank with immersion heater is used with automatic water filling facility.

Illumination:
Illumination plays important role in effective plant growth condition; therefore, we use high quality growth lights at three sides of the chamber. These lights are controlled through cyclic timer for 24X7 a week. These lights can be easily changed or replaced at user level.

Optional:
We also equip our plant growth chambers with some advance features such as PLC based HMI controller. It features color touch screen having display and control of temperature and humidity with data monitoring and storage and also facility USB interface to transfer data into pen drive. 30mm port hole for external wires and validation are also available 

FEATURES & ADVANTAGES:
Accuracy of temperature, humidity & light
Made according to plant height
Digital control panel
Digital light timer
Height adjustable shelves
Durable construction

One of the essential equipment of laboratory used to incubate samples under water at constan temperature (hot or cold). It comes in various design configurations, sizes and dimensions. Water baths are used in clinical and microbiology laboratories, universities, environmental research and even food technology; the applications include warming reagents, sample thawing, corrosion tests and bacteriological examinations etc.

STANDARD FEATURES
*Fitted with digital temperature controller.
*Excellent temperature accuracy & uniformity.
*High grade stainless steel interiorPowder coated exterior cabinet.
*High density glass wool insulation.
*Variety of optional accessories available.
*Large models are having internal circulation system with inbuilt corrosion resistant pump.
*External circulation available on demand.
*Various customized options available.

Specifications

Biosafety Cabinets are specialized workstations widely used in clinical, pharmaceutical, life science and industrial laboratories where experiments need highly contaminant free environment. Also known as biological safety cabinets and biohazard safety cabinets, these are made in three different class types such as Class 1, Class 2 and Class 3; in which Class 2 is widely used in microbiology laboratories because it provides protection to both product as well as personal. It is biosafety level factor which decides which BSC should be used in laboratory. These cabinets are considered safer than other clean benches because such BSCs effectively eliminate risks to operator / staff, samples and the environment from pathogenic biological agents (PBA) and microorganisms responsible for spreading airborne infection.

Types

We offer three types of class 2 biosafety cabinets are made. It is the type of work which decides which class 2 BSC should be used in laboratory. Below is short description about alltypes we offer:

Type A2: recirculate approximately 70% air and 30% exhaustType B1: recirculate approximately 30% air and 70% exhaustType B2: Does not recirculate but exhaust 100% air

Construction
Our cabinets are ergonomically designed to provide long service life. Only thick metal sheets and pipes are used in construction so that you may get the finest and safest Biosafety Cabinet in the market today. There are three different MOC used.
Complete Stainless Steel 304 / 316Inner Stainless Steel, Outer Mild SteelStainless Steel bench, rest mild Steel

* In compliance with class 100 For clean room with raw data report from NABL Certified Equipment.
*  Statically Balanced motor blower Assembly (Heavy Duty)
* Velocity at the output of HEPA is 90+-20FPM
* Less Than 60 DB
* Digital ptessure display on control panel
* highly transparent toughen front door
* Vibration of sytem is very low